Barcode Technologies 01442 872232
loginLogon     accountMy Account     cartMy basket contains 0 items










banner

Biometric Tri-Scan Reader for Symbol MC70

The Biometric Tri Scan reader is a reader that combines CONTACT SMART CARD, CONTACTLESS SMART CARD and FINGERPRINT BIOMETRIC CAPTURE. The biometric core uses a rugged, high image quality fingerprint area sensor. The Tri scan reader is compatible with most contact AND contact less Smart Cards including all Mifare cards. The contact less card reader is compatible with the CAC card and ICAO ePassports. The Tri Scan reader attaches as a snap-on unit to the base of the MC70 - the mechanical design of the module enables the attachment to remain compatible with existing MC70 accessories such as the desktop charge cradle and the car charger. The module may be quickly removed from the MC70, or semi-permanently attached with two screws. The fingerprint reader provides full enrolment, identification and verification functionality. Templates may be stored locally on the reader, or downloaded as required to the reader from the MC70 terminal. The sensor has a rugged coating to provide Electro Static Discharge immunity in excess of 12kV and the ability to withstand everyday wear and tear. The fingerprint sensor uses Active Capacitance Sensing. This method has the advantage of allowing a thick front coating to be used on the sensor which provides the sensor with its high ESD protection (12kV) and resistance to wear. It also allows the sensor to adapt to a wide range of skin types and conditions. The sensor has a high resolution (508 dpi) and high pixel resolution (256 level grey scale). These features ensure a high quality image is captured. In addition the design of the fingerprint sensor guides the user's finger to an optimum location to maximise accuracy.

In the enrolment process the fingerprint data is captured and a template is created by an algorithm running on the sensor. The template is based on the content and relationship of distinct areas identified from the image. The verification process is performed by comparing a captured template against a single previously stored template to verify the identity of a person. Alternatively the identification process compares a captured template to many stored templates to identify a person. Templates may be stored locally on the sensor or downloaded to it from a remote database or from the contact smartcard or RFID card. The contact smartcard reader is compliant to ISO7816-1,2,3,4, supports T=0 and T=1 protocols and Synchronous and Asynchronous mode. The reader is based on industry standards, including PC/SC, EMV, FINREAD and Common Criteria to address a wide range of applications across government, enterprise and financial sectors. The core chipset used in the Smart Card Reader is compliant with all crucial existing and emerging banking and IT standards and certifications. This means that the Smart Card Reader is ready for certification to Microsoft WHQL, EMV Level 1, Mondex, Entrust, and American Express.

The HF RFID reader provides the ability to read and write to a wide variety of transponders at 3.56 MHz including ISO 15693, ICODE (I & II) and the complete Mifare family of ISO14443 (A&B). Flash upgradeability of the RFID reader firmware provides future proofing of the reader. A Security Access Module (SAM) may be fitted to provide additional security features. Communication via the MC70 USB port is maintained enabling ActiveSync of the MC70 with a host device.


Fingerprint Sensor


Acquisition rate

15 frames/second

Identification time

(1:100) 1s typical

Enrolment time

5s typical

Verification time

(1:1) 0.5s typical

Acquisition rate

15 frames/second

False Rejection Rate (FRR)

Adjustable

False Acceptance Rate (FAR)

Adjustable

Sensor resolution

508dpi

Pixel array

256 x 360 pixels

Sensor area

12.8 x 18.0 mm

ESD protection

IEC 61000-4-2 Level 4 ±12kV

Image size

Approximately 100kbyte

Template size

100 to 540 bytes, typically 250byte

Smartcard Reader


Compliance

ISO7816-1,2,3,4

T=0, T=1 Protocol

Synchronous and Asynchronous mode

Connector

Meets ISO 7816-2, rated for >100 000 insertions

RFID Reader


RF Transmit Frequency

13.56MHz

Supported RFID Standards

ISO14443A, ISO14443B, ISO 15693, ISO 18000-3, ICODE

Supported Tag-ICs

Tag-it HF-I

Tag-it HF-I Light S

Philips ICODE SL2

Infineon ISO15693

MIFARE® Standard

MIFARE® 4k

MIFARE® Pro

MIFARE® Ultralight

MIFARE® DESFIRE

MIFARE® SmartMX

SLE 55Rxx

SRF55VxxP +S

SLE 66CL160S

SLE 66CLX320P

SR176

SRIX4K

LRI 12

LRI 64

LRI 512

EM4135

KSW Temp Sense

Sharp S

ASK GTML

ASK GTML2ISO

TOSMART P064

Jewel Tag (IRT0302B11 KSW)

ISO14443A Tags

ISO14443B Tags

ISO15693 Tags

 

Reading distance

Up to 5cm (2") using ISO7810 size credit card format transponders

SAM clock

3.39MHz

SAM VCC

5V

SAM type

Form factor compatible with GSM SIM footprint

 

Connection Interfaces

 

Physical interface

Serial and power in to charge MC70

Reader power supply

Powered from host terminal

ActiveSync

via USB

Physical Characteristics

 

Dimensions Weight 95g (3.35 oz)

90×82×32mm (3.54"x3.23"x1.26")

Enclosure material

Lexan EXL Polycarbonate

Colour

Grey

Material

finish Sparked surface

 

Mechanical attachment

Snap-on action with optional locking screws

Docking

Attachment maintains dock ability with Symbol docking cradle

for charging and ActiveSync

Environmental

 

Operating Temperature

-10°C to +50°C (14°F to 122°F)

Storage Temperature

-40°C to +60°C (-40°F to 140°F)

Humidity

Up to 90% Relative humidity Non Condensing

 

Drop specification

 

1.3m (4.26ft) to concrete, 6 drops per 6 sides over operating temperature; 1.5m (5ft) to concrete, 2 drops per 6 sides at ambient temperature 23ºC (73ºF)

Sealing

Internal components conformal coated

Electrostatic discharge

+/-12kV air discharge, +/-8kV direct discharge

Construction

RoHS compliant

Regulatory

 

EMI/RFI

EN 300 330, EN 301 489, CE marked

 

 

 


Warning: include() [function.include]: open_basedir restriction in effect. File(/infobox_spec.php) is not within the allowed path(s): (/var/www/vhosts/barcode-uk.com/:/tmp/) in /var/www/vhosts/barcode-uk.com/httpdocs/templates/content/product_spec.tpl.php on line 117
Product Listing Request a quote

About
Discontinued RFID Readers , Printers & Encoders

9 CANALSIDE NORTHBRIDGE ROAD BERKHAMSTED HERTFORDSHIRE HP4 1EG TEL: 01442 872232 FAX: 01442 871178