RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (8

RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22U holder is supplied.

P/N: RAM-HOL-ZE22U

Delivery: 1-2 weeks*

Request a Quote £99.25 (ex VAT) £119.10 (inc VAT)

RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (8") - This RAM Mounts GDS EZ-Rollâ€˜r holder is suitable for Zebra ET4x 8â€œ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PU holder is supplied.

P/N: RAM-GDS-DOCK-ZE20PU

Delivery: 1-2 days*

Request a Quote £82.01 (ex VAT) £98.41 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHLU holder is supplied.

P/N: RAM-HOL-ZE25PDHLU

Delivery: 1-2 weeks*

Request a Quote £281.34 (ex VAT) £337.61 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied.

P/N: RAM-HOL-ZE25PHLU

Delivery: 1-2 weeks*

Request a Quote £209.25 (ex VAT) £251.10 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PD2KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PD2KLU holder is supplied.

P/N: RAM-HOL-ZE10PD2KLU

Delivery: 1-2 weeks*

Request a Quote £133.61 (ex VAT) £160.33 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PLU holder is supplied.

P/N: RAM-HOL-ZE22PLU

Delivery: 1-2 weeks*

Request a Quote £157.45 (ex VAT) £188.94 (inc VAT)

RAM Mounts Form-Fit Holder (Key-locking) for Honeywell RT10 - This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9KLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalLockable with keyPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9KLU holder is supplied.

P/N: RAM-HOL-HON9KLU

Delivery: 1-2 weeks*

Request a Quote £88.94 (ex VAT) £106.73 (inc VAT)

RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47 - This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PHU holder is supplied.

P/N: RAM-HOL-HON12PHU

Delivery: 1-2 weeks*

Request a Quote £131.82 (ex VAT) £158.18 (inc VAT)

RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (10") - This RAM Mounts GDS EZ-Rollâ€˜r holder is suitable for Zebra ET4x 10â€œ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE21PDU holder is supplied.

P/N: RAM-GDS-DOCK-ZE21PDU

Delivery: 1-2 weeks*

Request a Quote £125.19 (ex VAT) £150.23 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10 - This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9CLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalLockable with combo-lockingPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9CLU holder is supplied.

P/N: RAM-HOL-HON9CLU

Delivery: 1-2 weeks*

Request a Quote £74.41 (ex VAT) £89.29 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra TC8300 - This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDHU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDHU holder is supplied.

P/N: RAM-HOL-ZE26PDHU

Delivery: 1-2 weeks*

Request a Quote £149.59 (ex VAT) £179.51 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10U:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10U holder is supplied.

P/N: RAM-HOL-ZE10U

Delivery: 1-2 weeks*

Request a Quote £47.25 (ex VAT) £56.70 (inc VAT)

RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8") - This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8â€œ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PDU holder is supplied.

P/N: RAM-GDS-DOCKL-ZE20PDU

Delivery: 1-2 weeks*

Request a Quote £152.54 (ex VAT) £183.05 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell CT50, CT60 & CT60 XP - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Honeywell CT50, CT60 & CT60 XP.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle and is also charged via USB-A.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON7CLU:Spring-loaded design for easy insertion and removalCharging functionStylus-Pen holderLockable with comboInput Connector: USB-A 2.0Input Cable Length: 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON7CLU holder is supplied.

P/N: RAM-HOL-HON7CLU

Delivery: 1-2 weeks*

Request a Quote £96.53 (ex VAT) £115.84 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra ET51/56 (10") - This RAM Mounts holder is suitable for Zebra ET5x 10.1â€œ Series with rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PDU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PDU holder is supplied.

P/N: RAM-HOL-ZE11PDU

Delivery: 1-2 weeks*

Request a Quote £100.26 (ex VAT) £120.31 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10 - This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PD2CLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with comboPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PD2CLU holder is supplied.

P/N: RAM-HOL-HON9PD2CLU

Delivery: 1-2 weeks*

Request a Quote £151.59 (ex VAT) £181.91 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET40/45 (10") - This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 10â€œ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PNLLU:Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKNLL-ZE21PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PNLLU holder is supplied.

P/N: RAM-HOL-ZE21PNLLU

Delivery: 1-2 weeks*

Request a Quote £100.35 (ex VAT) £120.42 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Getac ZX10 - This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDU holder is supplied.

P/N: RAM-HOL-GE4PDU

Delivery: 1-2 weeks*

Request a Quote £198.86 (ex VAT) £238.63 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra TC8300 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PLU:Spring-loaded design for easy insertion and removalCharging functionLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PLU holder is supplied.

P/N: RAM-HOL-ZE26PLU

Delivery: 1-2 weeks*

Request a Quote £103.25 (ex VAT) £123.90 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra TC8300 - This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDU:Spring-loaded design for easy insertion and removalCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDU holder is supplied.

P/N: RAM-HOL-ZE26PDU

Delivery: 1-2 weeks*

Request a Quote £91.25 (ex VAT) £109.50 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC8300 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHLU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHLU holder is supplied.

P/N: RAM-HOL-ZE26PHLU

Delivery: 1-2 weeks*

Request a Quote £161.61 (ex VAT) £193.93 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra TC53/58 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC53 & TC58 with or without Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-2U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderWith or without Rugged BootCharging functionLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-2U holder is supplied.

P/N: RAM-HOL-ZE17L-2U

Delivery: 1-2 weeks*

Request a Quote £84.79 (ex VAT) £101.75 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra L10 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra XSLATE L10.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15U:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15U holder is supplied.

P/N: RAM-HOL-ZE15U

Delivery: 1-2 weeks*

Request a Quote £58.82 (ex VAT) £70.58 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10") - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PCLU holder is supplied.

P/N: RAM-HOL-ZE11PCLU

Delivery: 1-2 weeks*

Request a Quote £100.91 (ex VAT) £121.09 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10") - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PDCLU holder is supplied.

P/N: RAM-HOL-ZE11PDCLU

Delivery: 1-2 weeks*

Request a Quote £116.01 (ex VAT) £139.21 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDLU holder is supplied.

P/N: RAM-HOL-ZE25PDLU

Delivery: 1-2 weeks*

Request a Quote £220.40 (ex VAT) £264.48 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDU holder is supplied.

P/N: RAM-HOL-ZE25PDU

Delivery: 1-2 weeks*

Request a Quote £199.42 (ex VAT) £239.30 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra TC73/78 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-NP-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderLockable with keyAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-NP-1U holder is supplied.

P/N: RAM-HOL-ZE17L-NP-1U

Delivery: 1-2 weeks*

Request a Quote £61.66 (ex VAT) £73.99 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra TC70/75, TC72/77 - This RAM Mounts holder is suitable for Zebra TC70, TC72, TC75 & TC77.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE7U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalCharging functionInput connector: 5.5mm DC ConnectorDC to USB-A Cable is includedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE7U holder is supplied.

P/N: RAM-HOL-ZE7U

Delivery: 1-2 weeks*

Request a Quote £58.18 (ex VAT) £69.82 (inc VAT)

RAM Mounts Form-Fit Holder for Getac ZX70 - This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM NFC Extender can be used to expand the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3NU:Easy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for the RAM NFC ExtenderAdditional information: This holder version will not support the Getac Rotating Hand Strap & Kickstand accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE3NU holder is supplied.

P/N: RAM-HOL-GE3NU

Delivery: 1-2 weeks*

Request a Quote £88.34 (ex VAT) £106.01 (inc VAT)

RAM Mounts Form-Fit Holder (key-Locking) for Zebra L10 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDKLU holder is supplied.

P/N: RAM-HOL-ZE15PDKLU

Delivery: 1-2 weeks*

Request a Quote £150.34 (ex VAT) £180.41 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra MC9300/9400 - This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PHLU holder is supplied.

P/N: RAM-HOL-ZE32PHLU

Delivery: 1-2 weeks*

Request a Quote £157.14 (ex VAT) £188.57 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHU holder is supplied.

P/N: RAM-HOL-ZE25PDHU

Delivery: 1-2 weeks*

Request a Quote £257.98 (ex VAT) £309.58 (inc VAT)

RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47 - This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDHU holder is supplied.

P/N: RAM-HOL-HON12PDHU

Delivery: 1-2 weeks*

Request a Quote £143.07 (ex VAT) £171.68 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PLU holder is supplied.

P/N: RAM-HOL-HON12PLU

Delivery: 1-2 weeks*

Request a Quote £127.02 (ex VAT) £152.42 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10 - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDCLU holder is supplied.

P/N: RAM-HOL-ZE15PDCLU

Delivery: 1-2 weeks*

Request a Quote £144.22 (ex VAT) £173.06 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (10") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 10.1â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PKLU holder is supplied.

P/N: RAM-HOL-ZE11PKLU

Delivery: 1-2 weeks*

Request a Quote £108.20 (ex VAT) £129.84 (inc VAT)

RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47 - This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDU holder is supplied.

P/N: RAM-HOL-HON12PDU

Delivery: 1-2 weeks*

Request a Quote £110.21 (ex VAT) £132.25 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PD2U:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp- Right or NFC-RepeaterInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PD2U holder is supplied.

P/N: RAM-HOL-ZE22PD2U

Delivery: 1-2 weeks*

Request a Quote £188.67 (ex VAT) £226.40 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra TC8300 - This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHU holder is supplied.

P/N: RAM-HOL-ZE26PHU

Delivery: 1-2 weeks*

Request a Quote £139.02 (ex VAT) £166.82 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5 mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PCLU holder is supplied.

P/N: RAM-HOL-ZE10PCLU

Delivery: 1-2 weeks*

Request a Quote £94.56 (ex VAT) £113.47 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra MC9300/9400 - This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PLU holder is supplied.

P/N: RAM-HOL-ZE32PLU

Delivery: 1-2 weeks*

Request a Quote £128.13 (ex VAT) £153.76 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Getac ZX10 - This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PU holder is supplied.

P/N: RAM-HOL-GE4PU

Delivery: 1-2 weeks*

Request a Quote £184.67 (ex VAT) £221.60 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10 - This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PCLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with comboPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PCLU holder is supplied.

P/N: RAM-HOL-HON9PCLU

Delivery: 1-2 weeks*

Request a Quote £125.65 (ex VAT) £150.78 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra ET80/85 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PDLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PDLU holder is supplied.

P/N: RAM-HOL-ZE22PDLU

Delivery: 1-2 weeks*

Request a Quote £193.79 (ex VAT) £232.55 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PKLU holder is supplied.

P/N: RAM-HOL-ZE10PKLU

Delivery: 1-2 weeks*

Request a Quote £102.00 (ex VAT) £122.40 (inc VAT)

RAM Mounts Holder for Zebra MC9300/9400 - This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32U:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32U holder is supplied.

P/N: RAM-HOL-ZE32U

Delivery: 1-2 weeks*

Request a Quote £58.28 (ex VAT) £69.94 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC22/27 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 with Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PLU:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with KeysInput Connector: USB-A Input Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PLU holder is supplied.

P/N: RAM-HOL-ZE24PLU

Delivery: 1-2 weeks*

Request a Quote £88.74 (ex VAT) £106.49 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10 - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PCLU holder is supplied.

P/N: RAM-HOL-ZE15PCLU

Delivery: 1-2 weeks*

Request a Quote £131.02 (ex VAT) £157.22 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22LU:Compatible with accessoriesEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22LU holder is supplied.

P/N: RAM-HOL-ZE22LU

Delivery: 1-2 weeks*

Request a Quote £122.20 (ex VAT) £146.64 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra MC9300/9400 - This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PHU holder is supplied.

P/N: RAM-HOL-ZE32PHU

Delivery: 1-2 weeks*

Request a Quote £135.49 (ex VAT) £162.59 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC22/27 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 without Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PL-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with keyInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PL-1U holder is supplied.

P/N: RAM-HOL-ZE24PL-1U

Delivery: 1-2 weeks*

Request a Quote £93.38 (ex VAT) £112.06 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10 - This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDCLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with comboPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDCLU holder is supplied.

P/N: RAM-HOL-HON9PDCLU

Delivery: 1-2 weeks*

Request a Quote £141.53 (ex VAT) £169.84 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10 - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15CLU holder is supplied.

P/N: RAM-HOL-ZE15CLU

Delivery: 1-2 weeks*

Request a Quote £75.80 (ex VAT) £90.96 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra ET60/65 - This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2HU holder is supplied.

P/N: RAM-HOL-ZE25PD2HU

Delivery: 1-2 weeks*

Request a Quote £261.96 (ex VAT) £314.35 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Getac ZX10 - This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4U holder is supplied.

P/N: RAM-HOL-GE4U

Delivery: 1-2 weeks*

Request a Quote £131.09 (ex VAT) £157.31 (inc VAT)

RAM Mounts Form-Fit Holder for Getac ZX70 - This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM Vent-Temp can utilize the vehicle's air vents to direct hot or cold air to the Getac ZX70.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3FU:Compatible with the Getac tablet accessoiresEasy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-TempAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-GE3FU holder is supplied.

P/N: RAM-HOL-GE3FU

Delivery: 1-2 weeks*

Request a Quote £89.06 (ex VAT) £106.87 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PHLU holder is supplied.

P/N: RAM-HOL-HON12PHLU

Delivery: 1-2 weeks*

Request a Quote £174.65 (ex VAT) £209.58 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra MC9300/9400 - This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDU holder is supplied.

P/N: RAM-HOL-ZE32PDU

Delivery: 1-2 weeks*

Request a Quote £118.55 (ex VAT) £142.26 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PLU holder is supplied.

P/N: RAM-HOL-ZE25PLU

Delivery: 1-2 weeks*

Request a Quote £175.41 (ex VAT) £210.49 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10CLU holder is supplied.

P/N: RAM-HOL-ZE10CLU

Delivery: 1-2 weeks*

Request a Quote £67.47 (ex VAT) £80.96 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU:Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25LU holder is supplied.

P/N: RAM-HOL-ZE25LU

Delivery: 1-2 weeks*

Request a Quote £131.59 (ex VAT) £157.91 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with Rugged Boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keysAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10KLU holder is supplied.

P/N: RAM-HOL-ZE10KLU

Delivery: 1-2 weeks*

Request a Quote £73.66 (ex VAT) £88.39 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PDKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5 mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PDKLU holder is supplied.

P/N: RAM-HOL-ZE10PDKLU

Delivery: 1-2 weeks*

Request a Quote £117.05 (ex VAT) £140.46 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (10") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 10.1â€œ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keysAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11KLU holder is supplied.

P/N: RAM-HOL-ZE11KLU

Delivery: 1-2 weeks*

Request a Quote £75.15 (ex VAT) £90.18 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra ET40/45 (8") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET4x 8â€œ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE20PDU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PDKLU holder is supplied.

P/N: RAM-HOL-ZE20PDKLU

Delivery: 1-2 weeks*

Request a Quote £122.26 (ex VAT) £146.71 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Honeywell RT10 - This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDU holder is supplied.

P/N: RAM-HOL-HON9PDU

Delivery: 1-2 weeks*

Request a Quote £122.82 (ex VAT) £147.38 (inc VAT)

RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8") - This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8â€œ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PD2U holder is supplied.

P/N: RAM-GDS-DOCKL-ZE20PD2U

Delivery: 1-2 weeks*

Request a Quote £161.13 (ex VAT) £193.36 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10 - This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDKLU holder is supplied.

P/N: RAM-HOL-GE4PDKLU

Delivery: 1-2 weeks*

Request a Quote £219.96 (ex VAT) £263.95 (inc VAT)

RAM Mounts EZ-Rollâ€™r Holder (key-locking) for Zebra ET40/45 (8") - This RAM Mounts EZ-Rollâ€˜r (key-locking) holder is suitable for Zebra ET4x 8â€œ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PKLU holder is supplied.

P/N: RAM-HOL-ZE20PKLU

Delivery: 1-2 weeks*

Request a Quote £120.73 (ex VAT) £144.88 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDHLU holder is supplied.

P/N: RAM-HOL-HON12PDHLU

Delivery: 1-2 weeks*

Request a Quote £167.46 (ex VAT) £200.95 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8") - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3â€œ & 8.4â€œ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5 mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PDCLU holder is supplied.

P/N: RAM-HOL-ZE10PDCLU

Delivery: 1-2 weeks*

Request a Quote £109.74 (ex VAT) £131.69 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10") - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1â€œ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11CLU holder is supplied.

P/N: RAM-HOL-ZE11CLU

Delivery: 1-2 weeks*

Request a Quote £67.86 (ex VAT) £81.43 (inc VAT)

RAM Mounts Form-Fit Holder (with key-locking) for Honeywell RT10 - This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDKLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDKLU holder is supplied.

P/N: RAM-HOL-HON9PDKLU

Delivery: 1-2 weeks*

Request a Quote £147.41 (ex VAT) £176.89 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra MC9300/9400 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDHLU holder is supplied.

P/N: RAM-HOL-ZE32PDHLU

Delivery: 1-2 weeks*

Request a Quote £169.55 (ex VAT) £203.46 (inc VAT)

RAM Mounts Form-Fit Holder (Key-locking) for Honeywell RT10 - This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PKLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PKLU holder is supplied.

P/N: RAM-HOL-HON9PKLU

Delivery: 1-2 weeks*

Request a Quote £134.94 (ex VAT) £161.93 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra L10 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keysAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15KLU holder is supplied.

P/N: RAM-HOL-ZE15KLU

Delivery: 1-2 weeks*

Request a Quote £81.45 (ex VAT) £97.74 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra MC9300/9400 - This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDHU holder is supplied.

P/N: RAM-HOL-ZE32PDHU

Delivery: 1-2 weeks*

Request a Quote £147.74 (ex VAT) £177.29 (inc VAT)

RAM Mounts Form-Fit Holder (key-locking) for Zebra TC73/78 - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-1U holder is supplied.

P/N: RAM-HOL-ZE17L-1U

Delivery: 1-2 weeks*

Request a Quote £87.60 (ex VAT) £105.12 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2U holder is supplied.

P/N: RAM-HOL-ZE25PD2U

Delivery: 1-2 weeks*

Request a Quote £207.69 (ex VAT) £249.23 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra MC9300/9400 - This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDLU holder is supplied.

P/N: RAM-HOL-ZE32PDLU

Delivery: 1-2 weeks*

Request a Quote £143.68 (ex VAT) £172.42 (inc VAT)

RAM Mounts Form-Fit Holder for Zebra TC22/27 - This RAM Mounts Form-Fit holder is suitable for Zebra TC22 & TC27 with Rugged Case.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24U holder is supplied.

P/N: RAM-HOL-ZE24U

Delivery: 1-2 weeks*

Request a Quote £44.36 (ex VAT) £53.23 (inc VAT)

RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10") - This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10â€œ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE21PDU holder is supplied.

P/N: RAM-GDS-DOCKL-ZE21PDU

Delivery: 1-2 weeks*

Request a Quote £157.79 (ex VAT) £189.35 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Honeywell RT10 - This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PU holder is supplied.

P/N: RAM-HOL-HON9PU

Delivery: 1-2 weeks*

Request a Quote £108.65 (ex VAT) £130.38 (inc VAT)

RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10 - This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PD2CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PD2CLU holder is supplied.

P/N: RAM-HOL-ZE15PD2CLU

Delivery: 1-2 weeks*

Request a Quote £154.82 (ex VAT) £185.78 (inc VAT)

RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (8") - This RAM Mounts EZ-Rollâ€˜r holder is suitable for Zebra ET4x 8â€œ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional informations: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20U.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCK-ZE20PDU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PDU holder is supplied.

P/N: RAM-HOL-ZE20PDU

Delivery: 1-2 weeks*

Request a Quote £90.75 (ex VAT) £108.90 (inc VAT)

RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10") - This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET40 & ET45 10â€œ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged BootLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Frame, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE21PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PKLU holder is supplied.

P/N: RAM-HOL-ZE21PKLU

Delivery: 1-2 weeks*

Request a Quote £125.12 (ex VAT) £150.14 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET40/45 (8") - This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 8â€œ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PNLLU:Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKNLL-ZE20PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PNLLU holder is supplied.

P/N: RAM-HOL-ZE20PNLLU

Delivery: 1-2 weeks*

Request a Quote £95.78 (ex VAT) £114.94 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65 - This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHU holder is supplied.

P/N: RAM-HOL-ZE25PHU

Delivery: 1-2 weeks*

Request a Quote £186.32 (ex VAT) £223.58 (inc VAT)

RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (8")

You recently viewed the following

Brodit holder, tilt swivel

TSC printhead TTP-2410MT, 8 dots/mm (203dpi)

RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell CT50, CT60 & CT60 XP

RAM Mounts - RAM Pod HD 24in. Vehicle Mount with Round Plate

TSC TTP-246M Pro, 8 dots/mm (203 dpi), RTC, display, TSPL-EZ, USB, RS232, LPT, Ethernet

RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8")

KOAMTAC Charging Cradle